3.3.2：增加预留量输出实例代码

若枫

3.3.2：增加预留量输出实例代码
- O5 B+ w4 o6 k$ M+ R/ n/ N
mastercam v9.1代码
fmt "XY STOCK TO LEAVE - " 2  xy_stock #Note format
fmt "Z STOCK TO LEAVE - "  2  z_stock  #Note format

pwrttparam     #Pre-read parameter data
      if prmcode = 10010, xy_stock = rpar(sparameter, 1)
. O; Z3 O, X6 y/ p5 @) w" t5 k      if prmcode = 10068, z_stock = rpar(sparameter, 1)

pparameter     #Read operation parameters
1 k; t- f& i4 L1 G) c( w, f      if prmcode = 10010, xy_stock = rpar(sparameter, 1)
      if prmcode = 10068, z_stock = rpar(sparameter, 1)

# I# v9 u4 L3 v9 \在换刀前面加入以下代码

$ x) ~. J: a. d8 ~7 }+ A6 s. dif xy_stock = 0 & z_stock = 0
5 Y2 i- F, H1 h( Xif xy_stock <> 0 & z_stock = 0, "(", xy_stock, ")", e
if xy_stock = 0 & z_stock <> 0, "(", z_stock, ")", e  
if xy_stock <> 0 & z_stock <> 0, "(", xy_stock, z_stock, ")", e
( e: H$ p6 z. C5 v8 q6 V: j+ B
mastercam X5代码
fmt "XY STOCK - " 2  xy_stock #Note format
fmt "Z STOC - "  2  z_stock  #Note format
( e8 w0 r) _8 d6 i: @4 F
0 G( s  A% D0 U7 p0 D3 V8 x& gpwrttparam$     #Pre-read parameter data
2 L4 N8 y) @, s7 B! O8 V      if prmcode$ = 10010, xy_stock = rpar(sparameter$, 1)
      if prmcode$ = 10068, z_stock = rpar(sparameter$, 1)
" p$ a6 C0 Z& w, `1 v: Z$ e) y6 x2 n
pparameter$     #Read operation parameters
' q, x4 i, R- v3 J* }      if prmcode$ = 10010, xy_stock = rpar(sparameter$, 1)
      if prmcode$ = 10068, z_stock = rpar(sparameter$, 1)

" M7 R, D( F! w; @
在换刀前面加入以下代码
6 |1 _; |1 c, V% l7 ]4 b
/ X4 @) X! L* ]- E" I' ?* wif xy_stock = 0 & z_stock = 0
; Y! a- }. d2 S& C" V' v, J  A# x! pif xy_stock <> 0 & z_stock = 0, "(", xy_stock, ")", e$
5 Y4 Z5 _+ [. J9 D$ k& [0 ]% O5 gif xy_stock = 0 & z_stock <> 0, "(", z_stock, ")", e$  
* x  M; h1 {8 rif xy_stock <> 0 & z_stock <> 0, "(", xy_stock, z_stock, ")", e$

2492848737

这些代码添加到个地方呢

ya574544187

学习了 老大 太厉害了