|
|
发表于 2011-8-14 00:03:41
|
显示全部楼层
回复 9# liujianyuhuayan
. e# c% d/ i3 n& w3 |" t4 n! \( q7 t0 x9 J2 [8 P8 m% F( ~
$ r$ ]% g1 {3 \; N
打开后处理,查找 i4 B7 g* ]7 |& S
ptoolcomment #Comment for tool
( g- J0 ]4 X8 [2 \& }* q2 z# n" H! p tnote = abs(t)
) k1 K5 `) }/ H8 J# t toffnote = tloffno
; u9 }1 u$ x' [, Q) t& j0 T strtool = ucase(strtool)# X* @/ I8 Y2 m( G! ]- b
stinsert2 = ucase(stinsert2)0 ?' K. L& W0 m, Z q2 ^6 |
!spaces5 v7 v/ J4 P+ j8 H2 b
spaces = zero3 h$ T9 P1 u8 a: i
"(", *tnote, *toffnote, ")", e- X& |: P; [4 q; g- ^' Y9 U
if posttype = two, # Lathe toolpath operation
0 {# F: e( Q& a9 F6 Q [
2 L1 {: D2 u7 l% l% }* i if tool_op = 64, # Drill operation
S# s0 S: H r. Y- _% Q "(", *strtool, ")", e# b% Q* X* U- U/ c# L
else,6 u9 Z4 @. w1 t1 r1 r8 N
"(", *strtool, " ", *stinsert, *stinsert2, ")", e' _4 U$ u& ]4 w0 V$ Q1 n6 i' F- R+ @0 o
]
4 ?2 x& z2 X# x+ f9 R else, # Mill toolpath operation
. p7 }2 S% _5 U7 n- x7 X8 h" f "(", *strtool, ")", e9 H) _$ w$ T6 E$ a
spaces = prv_spaces
6 ?/ R+ h) l$ R: u3 T! h
& y, n' W6 ]! X, A改为
- l6 J7 e- H- \9 \0 V2 Aptoolcomment #Comment for tool+ c. }6 K @( z& y
tnote = abs(t)
- U! R6 l7 ?" O$ U* C7 Y toffnote = tloffno# D5 P m: i: u; k8 Z+ n
strtool = ucase(strtool)
) d! ^- t6 R2 J! p0 w# t' U stinsert2 = ucase(stinsert2)
8 C) t& s+ S1 R# W( T8 _/ Q" i !spaces
7 w# W2 Q; o6 H' g spaces = zero$ _' A0 ?3 A) d2 d$ a
#"(", *tnote, *toffnote, ")", e
/ b* _9 S* t4 x # if posttype = two, # Lathe toolpath operation1 J) W( y* C I6 e. z/ `: ]
# [
% }' A. h+ U; x9 v+ l # if tool_op = 64, # Drill operation% s) S8 H& x3 z7 W, D
# "(", *strtool, ")", e
0 N! J2 k1 X! J, w+ N # else,
y2 ~8 z; M6 K # "(", *strtool, " ", *stinsert, *stinsert2, ")", e
3 \2 a8 Z: _. G #]
, Q- G4 S# P# H$ Z& c8 x2 o5 M #else, # Mill toolpath operation
1 D, W+ x* {7 @( y9 B # "(", *strtool, ")", e
) R! |% A1 Z" y6 a2 m1 Z spaces = prv_spaces |
|