3.3.2：增加预留量输出实例代码

若枫

3.3.2：增加预留量输出实例代码

mastercam v9.1代码
8 m5 D% Q& u3 M8 d% L# G$ r5 dfmt "XY STOCK TO LEAVE - " 2  xy_stock #Note format
  m: O( _+ p1 ]# Hfmt "Z STOCK TO LEAVE - "  2  z_stock  #Note format

. l9 }/ o! e1 P3 I' P. c. ^9 Gpwrttparam     #Pre-read parameter data
' _% R5 u2 y8 V8 q9 X; x      if prmcode = 10010, xy_stock = rpar(sparameter, 1)
      if prmcode = 10068, z_stock = rpar(sparameter, 1)

7 ]; E; q" ]( q* ~, i( K7 B- Dpparameter     #Read operation parameters
      if prmcode = 10010, xy_stock = rpar(sparameter, 1)
      if prmcode = 10068, z_stock = rpar(sparameter, 1)

在换刀前面加入以下代码
4 V% z$ ^- \' R/ b+ q/ D  H
+ D9 H" k* v2 ^, j/ s( jif xy_stock = 0 & z_stock = 0
if xy_stock <> 0 & z_stock = 0, "(", xy_stock, ")", e
if xy_stock = 0 & z_stock <> 0, "(", z_stock, ")", e  
! g. |; n, ^, q9 G: ^if xy_stock <> 0 & z_stock <> 0, "(", xy_stock, z_stock, ")", e

/ j7 x0 d& H- n% R0 hmastercam X5代码
fmt "XY STOCK - " 2  xy_stock #Note format
1 p$ _' q3 j( ffmt "Z STOC - "  2  z_stock  #Note format
5 ]1 B2 ^- H# y% l* g( n
/ N- a, {( A+ u; ~pwrttparam$     #Pre-read parameter data
& L5 ]& ?$ ]1 [- M7 ~$ ^      if prmcode$ = 10010, xy_stock = rpar(sparameter$, 1)
5 o, h" }& u9 ^4 j" K' ?' [      if prmcode$ = 10068, z_stock = rpar(sparameter$, 1)

pparameter$     #Read operation parameters
      if prmcode$ = 10010, xy_stock = rpar(sparameter$, 1)
6 N0 Z6 m& a9 f2 `      if prmcode$ = 10068, z_stock = rpar(sparameter$, 1)
- T3 y* b' i5 K/ e% m" Q/ j
" [9 I9 J+ s& L5 Y7 E; h8 W) m, @
在换刀前面加入以下代码
" k+ f' f; x  w; q$ q* I
! d0 [6 [/ B1 }+ Y: S- z' Kif xy_stock = 0 & z_stock = 0
if xy_stock <> 0 & z_stock = 0, "(", xy_stock, ")", e$
! O2 s) r8 p/ j1 L  Uif xy_stock = 0 & z_stock <> 0, "(", z_stock, ")", e$  
if xy_stock <> 0 & z_stock <> 0, "(", xy_stock, z_stock, ")", e$

2492848737

这些代码添加到个地方呢

ya574544187

学习了 老大 太厉害了