Renishaw FANUC 31使用中內孔測量程式

yit02yit02

Renishaw FANUC 31使用中內孔測量程式
0 K7 `0 B9 Q) O% Z# P7 G%
* p7 \/ d& ]5 `5 w! z6 k8 T<CEN-4-3>
G91G30Z0
0 ?2 ?9 Z1 l# iG54
$ W5 n4 b+ b6 s$ }) a) U7 T4 q+ aG90G0X0Y0
G43H01Z100.
(四點測量0度為起點A直徑XY為孔位S為數據指令M安全距離F安全高度)
G65P9656A0.R60.X0.Y0Z-5.S0M5.F100.
G0G90X0Y22.5
" S# I& H, c: g* P4 R  o#702=#108
% h& [5 W+ L3 c#703=#118
M01
(三點測量90度為起點A直徑XY為孔位S為數據指令M安全距離F安全高度)
" ~# l. @% u( Z% P- m' QG65P9654A90.R60.X0.Y0Z-5.S0M5.F100.
G0G90X0Y22.5
#704=#108
#705=#118
& y9 y" }5 _) j) ]5 V' {: }- QM01
G91G30Z0
G90X0Y0
3 g- p/ q; k' B* @9 \& ^) @M30
( ~* g* O  e0 G- T' ~) R. f%
, Q' l7 D9 ~1 w. c/ ~# H/ K3 X
7 V% T1 y6 @9 I1 t. @  F#108→實測尺寸
#118→實測尺寸公差
: Q. k& z2 p4 ~+ r. q" ~

%
O9654(* HOLE MEASURING 3 POINTS)
8 p. e' D; f% N, HG53
IF[#3008EQ1]GOTO999(PROGRAM RESTART)
#125=#4000(MAIN PRG NO.)
% b4 A4 u' r! W/ x#126=#4115(MACRO-NO.)
M98P9608(AMCS START)
#31=-3
+ I6 w, @1 V) d6 gM98P9615(PATTERN MEASURING)
M98P9609(AMCS END)
& `2 U1 z% e5 L% OM98P9601(HOLE & BOSS DATA)
M98P9600(PROCESS)
N999M99
' ?; _8 C+ y1 [' ]
%


6 `3 j5 b. ]+ @! b%
5 N& S+ R4 a: Q7 PO9656(* HOLE MEASURING 4 POINTS)
! n0 L% j6 g; u, c+ ^" p; `G53
1 r! |, |) A  f7 e; QIF[#3008EQ1]GOTO999(PROGRAM RESTART)
#125=#4000(MAIN PRG NO.)
' e$ N) j* \9 D2 ~5 s#126=#4115(MACRO-NO.)
M98P9608(AMCS START)
#31=-4
M98P9615(PATTERN MEASURING)
4 M0 ?7 \6 }9 O2 }M98P9609(AMCS END)
, C* h2 k% T4 qM98P9601(HOLE & BOSS DATA)
M98P9600(PROCESS)
7 t& W) @6 n5 M1 S, U4 s+ M" VN999M99

%