侧铣头用牙刀铣螺纹的程式怎末出

2675367140

我的系统是法兰克18i-MD

571937533

请问用什么程序用什么刀能把螺纹铣出来请高手赐教

若枫

回复 1# 2675367140


" s3 e- r, W0 r" H, B: \5 N9 ^    不知这个可不可以
! J: i/ ]% m% h6 N9 `9 K) P5 J5 s1 E%
O0000(T)
(DATE=DD-MM-YY - 15-03-12 TIME=HH:MM - 08:09)
(MCX FILE - T)
8 g. e, _  a' L8 G# Q7 H(NC FILE - D:\NC\T.NC)
(MATERIAL - ALUMINUM INCH - 2024)
  y5 v4 K; f$ h8 aG18 G20 G90 G40 G80 G64 G49 G0 M05
G91 G28 Z0. M05
T1 M6
( _% z. Q( o# Z7 P9 @& YG18 G0 G90 G54.1 P28 X0. Y-12.5S1500 M3
1 x2 a! V' y, B8 d  `; G" O) P# oG43 H1 Z0. M8
Y-4.6
* @& B1 T' G, x6 D6 Y1 ZG1 Y-4.4688 F10.
9 [* X/ ^9 [+ I2 ^# c0 vG41 D1 Z.65
" w6 ?) }8 _8 l) r' |' x6 ?G3 X.75 Y-4.4531 Z0. I.0933 K-.65
6 R- j0 F% B; xX-.75 Y-4.4219 I-.75 K0.
X.75 Y-4.3906 I.75 K0.
X0. Y-4.375 Z-.65 I-.6567 K0.
3 l1 Y) l. r( p/ n/ ~; s; A6 SG1 G40 Z0.
Y-3.8438
0 ]% T' n3 e9 e6 f9 OG41 D1 Z.65
0 h( U/ o- f: M1 a# CG3 X.75 Y-3.8281 Z0. I.0933 K-.65
+ a+ L' D: e+ }2 q7 r/ E$ EX-.75 Y-3.7969 I-.75 K0.
3 l0 |7 E+ V, [9 m. O0 dX.75 Y-3.7656 I.75 K0.
X0. Y-3.75 Z-.65 I-.6567 K0.
- D' Q2 W( A/ G0 d+ rG1 G40 Z0.
- K: n1 |: F% E3 |( A* s3 `6 w8 X' FY-3.2188
G41 D1 Z.65
! G" ]: v9 x3 _  t/ c6 ?G3 X.75 Y-3.2031 Z0. I.0933 K-.65
4 D( Q& Y3 _# u6 g9 t% TX-.75 Y-3.1719 I-.75 K0.
X.75 Y-3.1406 I.75 K0.
( |1 q9 e6 w; {& MX0. Y-3.125 Z-.65 I-.6567 K0.
5 H, e" J+ c, c, g) R$ D- t& ]. mG1 G40 Z0.
Y-2.5938
G41 D1 Z.65
G3 X.75 Y-2.5781 Z0. I.0933 K-.65
5 @  o3 l1 ~4 P# @% K# QX-.75 Y-2.5469 I-.75 K0.
X.75 Y-2.5156 I.75 K0.
X0. Y-2.5 Z-.65 I-.6567 K0.
G1 G40 Z0.
4 ~4 ~& s/ R, y+ }' `" a  c4 WG0 Y-4.6
8 W+ k& w' R1 r2 ^* yY-12.5
M9
G91 G28 Z0. M05
! c/ Z- g3 ?' c/ |7 C+ |( a' fG17
, e0 A* Z6 c5 {8 J0 I% ]5 W% z/ eM30
+ E! A7 Y2 [7 D( ^, X3 @* J$ l, A5 o%

cui-sam

用宏程序一次分N刀把牙铣出来.只需相应改座标X Y Z I J K,分清楚
0 L+ k5 L7 L" g* G- z1 E主轴座标方向,G2/G3的方向,就可侧面铣牙.

vinney777

旧帖子了，不过题目不错