3.3.2：增加预留量输出实例代码

若枫

3.3.2：增加预留量输出实例代码
' f4 c5 U6 W9 g; q( g
mastercam v9.1代码
fmt "XY STOCK TO LEAVE - " 2  xy_stock #Note format
9 g0 v; P( o" k! Ufmt "Z STOCK TO LEAVE - "  2  z_stock  #Note format
; W) Y) v/ |1 J1 c
pwrttparam     #Pre-read parameter data
      if prmcode = 10010, xy_stock = rpar(sparameter, 1)
. N- U0 y$ i; R* Q. y% O7 Y      if prmcode = 10068, z_stock = rpar(sparameter, 1)

pparameter     #Read operation parameters
+ i* T7 P7 j' [: W" N) q      if prmcode = 10010, xy_stock = rpar(sparameter, 1)
) X: f. t9 I7 L8 {1 F% t2 r      if prmcode = 10068, z_stock = rpar(sparameter, 1)

8 j7 t* z  c$ N+ D4 p1 [在换刀前面加入以下代码
, K9 h4 r& N9 n% D+ U6 r- B2 q
if xy_stock = 0 & z_stock = 0
5 |. U7 X# @' D% Sif xy_stock <> 0 & z_stock = 0, "(", xy_stock, ")", e
7 K( t9 O! |9 O+ _! X" G3 L2 ~- [4 {if xy_stock = 0 & z_stock <> 0, "(", z_stock, ")", e  
if xy_stock <> 0 & z_stock <> 0, "(", xy_stock, z_stock, ")", e

) C+ f( O4 j8 A9 Emastercam X5代码
0 o; N" `  a- S0 b8 Z1 L5 B0 rfmt "XY STOCK - " 2  xy_stock #Note format
fmt "Z STOC - "  2  z_stock  #Note format
& b! o6 ~! @8 D: F
pwrttparam$     #Pre-read parameter data
      if prmcode$ = 10010, xy_stock = rpar(sparameter$, 1)
$ y" \- M& n  P, S  k& d" a# U      if prmcode$ = 10068, z_stock = rpar(sparameter$, 1)
, T* S) y; c$ b4 L2 ]7 [
+ _4 k$ e8 D8 }- {" O- mpparameter$     #Read operation parameters
      if prmcode$ = 10010, xy_stock = rpar(sparameter$, 1)
1 \5 ^# D0 W. R7 }) {9 G6 U      if prmcode$ = 10068, z_stock = rpar(sparameter$, 1)
# `9 A' Y$ I; _  x) c
8 H; f3 ?! o$ L  ]" ^
在换刀前面加入以下代码

% y  B+ F! e! nif xy_stock = 0 & z_stock = 0
if xy_stock <> 0 & z_stock = 0, "(", xy_stock, ")", e$
9 [5 c" ]5 Q* Sif xy_stock = 0 & z_stock <> 0, "(", z_stock, ")", e$  
if xy_stock <> 0 & z_stock <> 0, "(", xy_stock, z_stock, ")", e$

2492848737

这些代码添加到个地方呢

ya574544187

学习了 老大 太厉害了