求助powermill,米克郎机床海德汉系统的后处理

zhanglei113513

求助powermill,米克郎机床海德汉系统的后处理，请哪位大哥奉献一下，本人不胜感谢。这个是本人的QQ邮箱27300165@QQ.com

vinney777

呵呵，有点无能为力了

694865935

上传两个我用过的，都是TNC-I530的控制器，一个机型是HSM400，还有一个是VCP600，不多说，上附件，

694865935

海德翰系统除了用它自己的格式，就是L代码，也支持ISO代码，不过采用ISO代码要注意几点
; y. G- ]/ n& p8 w2 {7 }* M( u因为海德翰系统如果使用ISO代码，要求每行都定义完整的G代码，它不像法兰克和三菱那有，碰到模态指令就是记忆前一条的G代码，所以每段都要求完整的格式，比如说
N0001 G02X-7.211Y-4.132R4.469*
N0002 X-7.632Y-5.141R5.91*   如果在法兰克和三菱机上，N0002这一行是可以读的，会记忆0001里的G02，按照0001里的G02来走。但是在海德翰系统上，就得把0002这一行也要加上G02，不能省略，不然就报警出错了，像下面这个格式就能跑了
8 m. J! W# |6 n. I2 I5 R' B
1 J6 N7 [( j' Q3 L$ XN0001 G02X-7.211Y-4.132R4.469*
N0001 G02X-7.632Y-5.141R5.91*

. A/ X5 w* R, l0 G/ J$ Q# u9 Q另外，海德翰系统的不读K，但支持圆弧走R，所以走圆弧麻烦请定义成R形式的。

) t  s# Q2 s9 A& z8 m# ?生成的NC程序副档名为.i   如E50. i之类

  y. K8 v4 e9 d8 y% M4 d以下是具体的一个加工程序请参照，谢谢！第一把刀T09是两个刀路合并的，走完第一个刀路后抬到刀具初始下刀点，再开始走第二条程序。



% z, ?0 z( \  F%O0001G71*      程序头
  W& T% g' R: n7 m. [) q2 s6 \;(TOOL DATE MON SEP 24 09:43:47 2012)*     NC程序生成时间
;(TOOL TYPE DIA=8.0000,FLAT)*             刀具信息
4 m8 F3 R) d. O! V, f& RN0001G17T09S10000*         换刀指令
* c# L6 V1 D5 CN0002M03*
* J3 \& ^) n6 x5 G; A0 k. |1 oN0003G4F20*
$ f+ _, A+ l3 ^. U( pN0004G583Q350=+0Q361=+3Q362=+0.01Q359=+0*            
N0005G00G90G40*
N0006G62T0.005*
N0007M03*         从N02-N07为红外量刀器动作时间，可以固定成这个格式。
N0008G00G17G90X0.Y0.*     开始加工
N0009Z100.*
N0010S10000M03*
3 n' [9 c- N6 Z, P. [N0011G00X-84.526Y7.849*
N0012G00Z4.*
N0013M08*     开切削液
2 ], T$ j3 n; L% i2 |7 hN0014G01Z-1.F1500*
3 [/ c' n- z6 c2 FN0015G01X87.569F2000*
( m1 `& E) K4 b' N2 K! VN0016G01X-84.526Y2.849*
7 C$ A7 Z% q6 E( b  H: r. a7 ZN0017G01X87.569*
N0018G01X-84.526Y-2.151*
  c) H4 v  D9 V  VN0019G01X87.569*
% F4 O/ f7 x3 d; g" yN0020G01X-84.526Y-7.151*
N0021G01X87.569*
N0022G01X-84.526Y-12.151*
# C" N4 U1 o5 L2 X8 LN0023G01X87.569*
/ @: D7 t- l+ `$ S& J1 t5 E8 LN0024G01X-84.526Y-17.151*
N0025G01X87.569*
3 P" U4 {7 K7 @9 ]N0026G01X-84.526Y-22.151*
3 W+ @: n; x6 MN0027G01X87.569*
N0028G00Z10.*
N0029M09M05*     关水，主轴停转（因为第二条刀路的S不一样，出于保护机台，主轴先停止）
N0030G00Z100.*      抬刀到刀具初始Z位置（这条程序中我编程时设的刀具初始位置是0，0，100）
N0031G00X0.Y0.*     抬刀到刀具初始XY位置
3 n! m3 ?. w  r/ T/ ~" Z+ e! Y( JN0033S13000M03*      开始加工第二条刀路，按第二条刀路设定的主轴转速启动
) a+ k" {0 |* S4 y; U8 ^1 JN0034G00X69.*
6 ?4 r- ]. |1 G0 v& uN0035G00Z4.*
; U5 t6 y$ W3 U+ _+ `N0036M08*         重新开水
- N6 Q2 s- S: n- Q# LN0037G01Z-1.F1500*
! B* E2 L7 O' B0 nN0038G01Y5.F1000*
6 R) {* D6 o, i* Y- X* {N0039G03X64.Y0.R5.*
: A9 c& a. p4 D) ]6 M& [N0040G01Y-44.*
, \2 x$ P+ r+ V: @" CN0041G01X-64.*
& m$ j$ a& Z  F2 z7 j# `- [# jN0042G01Y44.*
N0043G01X64.*
1 k5 I3 ]3 G* JN0044G01Y0.*
N0045G03X69.Y-5.R5.*
N0046G01Y0.*
N0047G01Z-2.*
N0048G01Y5.*
N0049G03X64.Y0.R5.*
8 \& O3 X& o* y: t; W8 NN0050G01Y-44.*
3 h. F9 M* M" E3 {/ I$ rN0051G01X-64.*
( U3 B$ d4 v, C$ Q3 C4 p/ I/ xN0052G01Y44.*
) c* V/ A5 E$ `! ]; T; ?  ^* |( JN0053G01X64.*
N0054G01Y0.*
2 w$ z: F2 S8 JN0055G03X69.Y-5.R5.*
N0056G01Y0.*
( O, k9 S% h( `% TN0057G01Z-3.*
5 _% G. ~$ r. g, N" _3 N4 C. z) aN0058G01Y5.*
N0059G03X64.Y0.R5.*
+ L* B- w0 L- T. M" N3 SN0060G01Y-44.*
9 L5 }* q& L) G2 ~N0061G01X-64.*
N0062G01Y44.*
/ u4 S# S' L) e& k- RN0063G01X64.*
N0064G01Y0.*
N0065G03X69.Y-5.R5.*
7 w3 l9 A- S( o+ A+ p3 @* mN0066G01Y0.*
+ R' f6 E! C/ X1 C5 m/ `N0067G00Z10.*
N0068M09M05*
: c4 s1 a6 o% `) y/ vN0069G00Z100.*
N0070G00X0.*
N0071M140MBMAX*   走完第一把刀，抬起Z轴到极限范围，准备换刀
* k6 Y1 V- B, M  P* {;(TOOL DATE SAT SEP 22 15:35:29 2012)*
;(TOOL TYPE DIA=6.0000,FLAT)*
N0072G17T08S15000*    换第二把刀8号刀
N0073M03*
" `# w/ X, R9 h" I% o/ o7 ]3 LN0074G4F20*
# W. u' ^! x  N/ _4 a( r: VN0075G583Q350=+0Q361=+3Q362=+0.01Q359=+0*
* N  u0 U! f) cN0076G00G90G40*
, }5 ?5 v% v) h; w* a- qN0077G62T0.005*
N0078M03*        量刀
N0079G00G17G90X0.Y0.*
; M/ a1 m  v1 n5 l1 k# bN0080Z100.*
N0081S15000M03*
, k- K; D9 z; A) l+ r- Y5 KN0082G00X0.347Y2.99*
- O  g! A$ Q7 k" l# z7 oN0083G00Z4.*
) ^5 x. n& ?# x( jN0084M08*
% d& ?- q' F9 J+ ~% X" @5 y: |N0085G01Z-1.F1500*
N0086G01X-0.141Y2.988Z-1.026F1000*
N0087G01X-0.623Y2.906Z-1.051*
N0088G01X-1.085Y2.748Z-1.077*
N0089G01X-1.516Y2.516Z-1.103*
0 J% S5 `0 Q+ Z$ }N0090G01X-1.903Y2.218Z-1.128*
N0091G01X-2.236Y1.861Z-1.154*
N0092G01X-2.507Y1.454Z-1.179*
N0093G01X-2.709Y1.009Z-1.205*
4 }3 G5 G/ t+ B) J0 g( lN0094G01X-2.835Y0.537Z-1.231*
N0095G01X-2.884Y0.05Z-1.256*
! h* D5 l3 J; y+ i( o( F' I0 T$ i! lN0096G01X-2.852Y-0.437Z-1.282*
$ Q8 J& F: I9 Q" x& |+ BN0097G01X-2.742Y-0.914Z-1.308*
N0098G01X-2.556Y-1.365Z-1.333*
N0099G01X-2.299Y-1.781Z-1.359*
6 p+ m8 c. T! J; c0 {  RN0100G01X-1.978Y-2.15Z-1.385*
; z7 A4 _' [+ Z+ U- y6 aN0101G01X-1.601Y-2.461Z-1.41*
" s/ `' k* ]8 E& F% @/ SN0102G01X-1.179Y-2.707Z-1.436*
N0103G01X-0.722Y-2.882Z-1.462*
N0104G01X-0.244Y-2.979Z-1.487*
N0105G01X0.245Y-2.998Z-1.513*
, B, U8 J6 h) j8 W: NN0106G01X0.73Y-2.938Z-1.538*
& v1 k$ T  f$ u# v# c) xN0107G01X1.198Y-2.799Z-1.564*
N0108G01X1.638Y-2.586Z-1.59*
N0109G01X2.038Y-2.305Z-1.615*
N0110G01X2.386Y-1.962Z-1.641*
+ C( y7 \* W# h: I+ {6 |& WN0111G01X2.675Y-1.567Z-1.667*
/ k, e7 D, r- b8 v7 m1 @N0112G01X2.895Y-1.131Z-1.692*
N0113G01X3.042Y-0.665Z-1.718*
  o0 ^* m. n2 _' D, d. _! q( H- bN0114G01X3.111Y-0.181Z-1.744*
9 _1 g8 y3 J6 PN0115G01X3.1Y0.307Z-1.769*
N0116G01X3.01Y0.788Z-1.795*
N0117G01X2.844Y1.247Z-1.821*
N0118G01X2.605Y1.674Z-1.846*
N0119G01X2.3Y2.056Z-1.872*
N0120G01X1.937Y2.383Z-1.897*
N0121G01X1.526Y2.647Z-1.923*
5 p3 x6 ]  F3 X+ tN0122G01X1.077Y2.841Z-1.949*
6 X1 G' a1 s7 f( p6 o; J; k' fN0123G01X0.603Y2.959Z-1.974*
N0124G01X0.116Y2.999Z-2.*
" E( u* l: h; iN0125G01X-22.523*
N0126G01Y-2.123*
; M, p! S" {9 d0 m' Y8 S- ~$ lN0127G01X22.755*
/ _* E5 t- `& S; g1 X  o) yN0128G01Y2.999*
9 |( {* O8 ?$ A) [N0129G01X0.116*
% v& F- ^: k( A) MN0154G01Y17.999*
N0155G01X-37.523*
  I; m. t1 P, z4 g1 c* ^N0156G01Y-17.123*
N0157G01X37.755*
N0158G01Y17.999*
N0159G01X0.116*
1 O# d( s- @: YN0160G01Y20.999*
N0161G01X-40.523*
N0162G01Y-20.123*
N0163G01X40.755*
N0164G01Y20.999*
N0165G01X0.116*
. D5 ~# _/ s" k5 z' v2 PN0166G01Y23.999*
N0167G01X-43.523*
7 Q; f1 F+ m/ yN0168G01Y-23.123*
N0169G01X43.755*
/ o7 x5 R1 q; }# A( m$ @N0170G01Y23.999*
N0171G01X0.116*
N0172G01Y26.999*
/ i, O4 ]* H. p2 W# cN0173G01X-46.523*
N0174G01Y-26.123*
! F9 z. \. D$ a' h6 y; J2 wN0198G01Y-38.123*
8 z5 r& c3 a. R3 n/ A: mN0199G01X58.755*
N0200G01Y38.999*
N0201G01X0.116*
N0202G01X-2.884*
2 u* ~+ x- w; b6 I0 y; w3 Y* S0 lN0203G01Y37.499*
5 ]0 c, T2 T1 |& w5 ?+ g+ J7 TN0204G00Z10.*
% S& z6 H" C6 ~" HN0205M09M05*
3 `9 O* C) b) v0 j3 Q; EN0206G00Z100.*
) y5 q4 B. N! _% \. U* w* p! aN0207G00X0.Y0.*
N0208M140MBMAX*
;(TOOL DATE THU SEP 20 15:07:52 2012)*
3 A% ~9 t% l- {0 G7 h( m- M! o' v;(TOOL TYPE DIA=8.0000,FLAT)*
# H7 Y/ f6 S8 ]" ?% X9 _N0209G17T09S10000*        换第三把刀9号刀
( Y" Z9 d* I% F3 z; V) \N0210M03*
N0211G4F20*
N0212G583Q350=+0Q361=+3Q362=+0.01Q359=+0*
( h) k; [0 N* lN0213G00G90G40*
N0214G62T0.005*
N0215M03*      量刀
N0216G00G17G90X0.Y0.*
N0217Z100.*
N0218S10000M03*
2 d9 [% x5 {$ V; O* ]7 X" z7 gN0219G00X68.*
N0220G00Z4.*
N0221M08*
N0222G01Z-1.F1500*
9 ^* c, L# E1 f- g3 \6 HN0223G01Y5.F1000*
. Q% O5 ?" k, t' T3 B' ^N0224G03X63.Y0.R5.*
' H" t0 o8 T2 B* aN0225G01Y-43.*
N0226G01X-63.*
9 O  R( D, H$ y! W1 oN0227G01Y43.*
4 H/ U) v. N$ W' i0 IN0228G01X63.*
N0229G01Y0.*
, z& N4 \) J1 e3 G/ S, i: F' i* G# w, FN0230G03X68.Y-5.R5.*
" c3 t8 |) B% ~; FN0231G01Y0.*
  K2 O( M/ z1 n; l/ t) E, @N0232G01Z-2.*
N0233G01Y5.*
; \7 A  y! S4 B! }) h% {N0234G03X63.Y0.R5.*
N0235G01Y-43.*
* |3 D0 e- J$ IN0236G01X-63.*
2 r6 W8 n6 c4 Z' b( X+ M" gN0237G01Y43.*
7 `' }0 E4 H2 D# Y' {N0238G01X63.*
3 Q- b6 A/ |1 I7 o# I  o; oN0239G01Y0.*
! o% W" r  K. M) M, i0 ^3 tN0240G03X68.Y-5.R5.*
$ Z/ E! M+ f2 ?& S7 Z" q! rN0241G01Y0.*
/ J- \; G, f: G  o8 Y, |N0242G01Z-3.*
N0243G01Y5.*
N0244G03X63.Y0.R5.*
; N9 ]  ^& |: m, V, R) S! oN0245G01Y-43.*
/ _6 E7 Q5 ~# i% y/ o( T7 h) ^0 Y7 sN0246G01X-63.*
6 z4 U9 _, ?! h" g& ]6 N4 YN0247G01Y43.*
% R" h; A8 D$ D" x' SN0248G01X63.*
( R' s2 D* v1 o; f& p+ j$ j. ^N0249G01Y0.*
# @' R8 [& d0 b. G! bN0250G03X68.Y-5.R5.*
N0251G01Y0.*
: L' F; m6 D* C# [+ pN0252G00Z10.*
N0253M09M05*
N0254G00Z100.*
N0255G00X0.*
% T( `; `" Y1 u9 p4 lN0256M140MBMAX*

* L( f& H) q8 \8 l2 T" P程序结束，谢谢！

694865935

这个是海德翰格式的程序，产生的程序副档名请定义成.h  如E50.h

$ g( j7 }* S( E5 p# K: y, @5 y: u
* U  o- D5 O  f. W( J3 P% p0001 BEGIN PGM 3333 MM
: ]5 w1 T6 T% ]: ~0002 BLK FORM 0.1 Z X-100. Y-100. Z-50.
0003 BLK FORM 0.2 X+100 Y+100 Z+0.05
3 ^7 o" U6 j+ e' Y) N0004 ;(F BLADE=2)
0005 ;(F DIAM=8.0000,FLAT)
0006 TOOL CALL 09 Z S10000   呼叫刀具
0007 M03
9 g7 Q! A* Z/ X( W' H. H0087 CYCL DEF 9.0 DWELL TIME
9 F& a: L+ J( p# \% V) d. D2 f0087 CYCL DEF 9.1 DWELL 20   这两行是暂停20秒
0008 TCH PROBE 583 TOOL SETTING LEN ~
9 D+ A3 E# p6 k, P9 g7 l0009 Q350=+0  ;MEASURING TYPE ~
0010 Q361=+3  ;NUMBER OF MEASURINGS ~
0011 Q362=+0.01  ;DISPERSION TOLERANCE ~
4 p" `% x: v3 Z0012 Q359=+0  ;ADD. LENGTH CORRECT.  这几行是量刀，我用的是G583的指令，
0013 CYCL DEF 32.0 TOLERANCE
2 E' V9 c+ K9 F; ?0014 CYCL DEF 32.1 T0.007  加工精度定义
* ]- K: ?( F) U) }0015 M03
3 i$ _. D* ~0 {& k' h! Y. ~7 s0016 LX0.Y0.FMAX
% x& `9 y6 r) j. k# x5 R2 ]0017 LZ100.FMAX
1 c' w2 C0 E/ g- R0018 LX-84.526Y7.849Z100.FMAX
2 X$ T5 f' h8 x( n# ~; c0019 LX-84.526Y7.849Z4.FMAX
0020 M08
0021 LX-84.526Y7.849Z-1.F1500
0022 LX87.569Y7.849Z-1.F2000
2 D5 a( V  c1 W( |7 L1 ?: T0 b0023 LX-84.526Y2.849Z-1.
0024 LX87.569Y2.849Z-1.
0025 LX-84.526Y-2.151Z-1.
- K% c2 \' ]3 A) i0026 LX87.569Y-2.151Z-1.
0027 LX-84.526Y-7.151Z-1.
3 _) s$ o, o2 n: O6 `0028 LX87.569Y-7.151Z-1.
4 o0 z/ j' o8 A# M0029 LX-84.526Y-12.151Z-1.
0030 LX87.569Y-12.151Z-1.
0031 LX-84.526Y-17.151Z-1.
0032 LX87.569Y-17.151Z-1.
0033 LX-84.526Y-22.151Z-1.
0034 LX87.569Y-22.151Z-1.
& U/ V$ ]: A# V0035 LX87.569Y-22.151Z10.FMAX
) V* q4 P5 v% s5 Q( m5 ^0036 LX87.569Y-22.151Z100.FMAX
$ G9 W; w( K$ l0037 LX0.Y0.Z100.FMAX
  L, f' i+ a) F( v3 Q0038 CYCL DEF 32.0 TOLERANCE
3 V  e2 ]; v' v9 o, V0039 CYCL DEF 32.1   这里是两条刀路合并的，同一把刀，走完第一个刀路抬到安全起始高度
3 E( X" X8 {$ Q* Q0 d4 Q0040 LX69.Y0.Z100.FMAX
) v" m2 O6 K; \& s3 a9 ]$ y% O! k0041 LX69.Y0.Z4.FMAX
0042 M08
0043 LX69.Y0.Z-1.F1500
6 _, n4 `2 q& ^8 P0044 LX69.Y5.Z-1.F1000
0045 CCX69.Y0.
: U6 }' B4 R) S9 Z: X5 j% ]0 i( B0 J0046 CX64.Y0.DR+
  H, }' w+ J* c+ u$ o! E0047 LX64.Y-44.Z-1.
0048 LX-64.Y-44.Z-1.
0049 LX-64.Y44.Z-1.
: J  ], n; ]7 ~0050 LX64.Y44.Z-1.
0051 LX64.Y0.Z-1.
0052 CCX69.Y0.
% q1 j+ e6 J; N- ?% |- o! W0053 CX69.Y-5.DR+
, H' H2 u) G2 k0054 LX69.Y0.Z-1.
1 D% W% y: Y1 W1 J% h: q) u0055 LX69.Y0.Z-2.
- z$ d' j7 J4 a7 n! \0056 LX69.Y5.Z-2.
0057 CCX69.Y0.
0058 CX64.Y0.DR+
: C0 ]! e2 ~) n5 i0059 LX64.Y-44.Z-2.
0060 LX-64.Y-44.Z-2.
0061 LX-64.Y44.Z-2.
0062 LX64.Y44.Z-2.
$ m" ]" t9 R, d& h- q$ H, N0063 LX64.Y0.Z-2.
0064 CCX69.Y0.
0065 CX69.Y-5.DR+
0066 LX69.Y0.Z-2.
0067 LX69.Y0.Z-3.
0068 LX69.Y5.Z-3.
0069 CCX69.Y0.
' q1 q. @$ M5 B2 z- h" Y- Y0070 CX64.Y0.DR+
0071 LX64.Y-44.Z-3.
0072 LX-64.Y-44.Z-3.
0073 LX-64.Y44.Z-3.
0074 LX64.Y44.Z-3.
" _% x7 D! B/ b  o5 T  Y0075 LX64.Y0.Z-3.
% w2 h: d& m1 k4 Y  }: I& S0076 CCX69.Y0.
0077 CX69.Y-5.DR+
0078 LX69.Y0.Z-3.
0079 LX69.Y0.Z10.FMAX
0080 LX69.Y0.Z100.FMAX
0081 LX0.Y0.Z100.FMAX     
: I' G2 h  n) L. U, O5 D0082 CYCL DEF 32.0 TOLERANCE
3 G! h0 V* Q0 `" ?# v0083 CYCL DEF 32.1     程序结束
1 y6 \) e, I  a3 o% I0084 ;(F BLADE=2)
0085 ;(F DIAM=6.0000,FLAT)
0086 TOOL CALL 08 Z S15000 换刀
0087 M03
# N; E+ i% M5 M( s" V4 _0087 CYCL DEF 9.0 DWELL TIME
0087 CYCL DEF 9.1 DWELL 20 暂停20秒暖机
0088 TCH PROBE 583 TOOL SETTING LEN ~
0089 Q350=+0  ;MEASURING TYPE ~
0090 Q361=+3  ;NUMBER OF MEASURINGS ~
" {8 w& y. Q0 P0 Y3 M0091 Q362=+0.01  ;DISPERSION TOLERANCE ~
0092 Q359=+0  ;ADD. LENGTH CORRECT.
0093 CYCL DEF 32.0 TOLERANCE
0094 CYCL DEF 32.1 T0.007
9 O$ m; P/ Z& a' T0095 M03
- w4 G7 @1 @+ N9 M; G* w6 |0096 LX0.Y0.FMAX
0097 LZ100.FMAX
0098 LX0.347Y2.99Z100.FMAX
0099 LX0.347Y2.99Z4.FMAX
- d, u' z5 j% w) o8 m# _+ {0100 M08
0101 LX0.347Y2.99Z-1.F1500
/ I" E3 P7 h% T, M7 D0102 LX-0.141Y2.988Z-1.026F1000
/ Z; L. F: x( s+ k/ c0103 LX-0.623Y2.906Z-1.051
0104 LX-1.085Y2.748Z-1.077
0105 LX-1.516Y2.516Z-1.103
0106 LX-1.903Y2.218Z-1.128
0107 LX-2.236Y1.861Z-1.154
0108 LX-2.507Y1.454Z-1.179
9 l  Y& q) k+ A+ q6 y0109 LX-2.709Y1.009Z-1.205
' r9 t$ w( ^6 `7 z0110 LX-2.835Y0.537Z-1.231
0111 LX-2.884Y0.05Z-1.256
0112 LX-2.852Y-0.437Z-1.282
: @) k+ l5 T& `! k0113 LX-2.742Y-0.914Z-1.308
0 S+ ~. z) y* G* P1 o! L8 {2 w0114 LX-2.556Y-1.365Z-1.333
7 M0 n* q) {8 L" f9 F0115 LX-2.299Y-1.781Z-1.359
0116 LX-1.978Y-2.15Z-1.385
0117 LX-1.601Y-2.461Z-1.41
: U- w5 r% P3 ~3 q" W0118 LX-1.179Y-2.707Z-1.436
0119 LX-0.722Y-2.882Z-1.462
0120 LX-0.244Y-2.979Z-1.487
9 w; z& u& V8 V+ b! t0 D  H0121 LX0.245Y-2.998Z-1.513
0122 LX0.73Y-2.938Z-1.538
0123 LX1.198Y-2.799Z-1.564
( A) W; K5 ^4 d, j" M4 W0124 LX1.638Y-2.586Z-1.59
, t  \1 f) m0 j8 f9 K2 j# b7 ~0125 LX2.038Y-2.305Z-1.615
0126 LX2.386Y-1.962Z-1.641
0127 LX2.675Y-1.567Z-1.667
" ?; z9 |0 C' x  f! w: \/ x, H0128 LX2.895Y-1.131Z-1.692
3 ]/ n  b! i5 H1 f  \0129 LX3.042Y-0.665Z-1.718
0130 LX3.111Y-0.181Z-1.744
0131 LX3.1Y0.307Z-1.769
0132 LX3.01Y0.788Z-1.795
$ F* ]: F9 N8 \' t2 n0 O2 b0 n0133 LX2.844Y1.247Z-1.821
0134 LX2.605Y1.674Z-1.846
8 k3 |/ t7 U3 T" c6 I6 [0135 LX2.3Y2.056Z-1.872
0136 LX1.937Y2.383Z-1.897
. W; H) @2 T6 O0137 LX1.526Y2.647Z-1.923
0138 LX1.077Y2.841Z-1.949
0139 LX0.603Y2.959Z-1.974
0140 LX0.116Y2.999Z-2.
. Y9 t0 G( G& ]' J- W/ w; J0141 LX-22.523Y2.999Z-2.
0142 LX-22.523Y-2.123Z-2.
& |, y8 A! R# h0143 LX22.755Y-2.123Z-2.
0144 LX22.755Y2.999Z-2.
0145 LX0.116Y2.999Z-2.
0146 LX0.116Y5.999Z-2.
0 Y! m& g$ R1 }7 ^0147 LX-25.523Y5.999Z-2.
6 m9 ?+ Q  w7 s) t  H* l0148 LX-25.523Y-5.123Z-2.
) t, K/ M. m3 S+ Q% n4 G) K0149 LX25.755Y-5.123Z-2.
0150 LX25.755Y5.999Z-2.
0151 LX0.116Y5.999Z-2.
0152 LX0.116Y8.999Z-2.
0153 LX-28.523Y8.999Z-2.
) M# z0 ?1 ?* R# W0154 LX-28.523Y-8.123Z-2.
1 c8 u+ n5 H. _) E* M0155 LX28.755Y-8.123Z-2.
" v/ ~1 @* s5 B& k& c0156 LX28.755Y8.999Z-2.
, p1 U2 U/ m# w0 P* W9 E) I0157 LX0.116Y8.999Z-2.
& ?0 [0 F) {5 x; s0158 LX0.116Y11.999Z-2.
5 r2 T5 J, a, X' F4 L* ]0159 LX-31.523Y11.999Z-2.
0160 LX-31.523Y-11.123Z-2.
1 U: @' O7 {$ L5 n) \% q3 G$ }0161 LX31.755Y-11.123Z-2.
' j$ c9 r( v! l$ R  Z* _* X0162 LX31.755Y11.999Z-2.
* i- e3 u& A7 R2 w0163 LX0.116Y11.999Z-2.
0164 LX0.116Y14.999Z-2.
0165 LX-34.523Y14.999Z-2.
0166 LX-34.523Y-14.123Z-2.
0167 LX34.755Y-14.123Z-2.
0168 LX34.755Y14.999Z-2.
( c: V. ?& A5 @  Y$ u7 A! e0169 LX0.116Y14.999Z-2.
0170 LX0.116Y17.999Z-2.
0171 LX-37.523Y17.999Z-2.
7 r6 c+ V1 U/ G& s0172 LX-37.523Y-17.123Z-2.
# E. {/ I* p$ Z- S# F9 o0173 LX37.755Y-17.123Z-2.
2 A3 z6 m* g+ c- {0174 LX37.755Y17.999Z-2.
0175 LX0.116Y17.999Z-2.
0176 LX0.116Y20.999Z-2.
0 m- ]1 J9 K: z- S0177 LX-40.523Y20.999Z-2.
7 G+ o- t& T. U! s6 b+ [! v0178 LX-40.523Y-20.123Z-2.
+ w; |" m1 R9 G0179 LX40.755Y-20.123Z-2.
0180 LX40.755Y20.999Z-2.
( \: T% F! T- a+ U) `0181 LX0.116Y20.999Z-2.
  [1 t! b6 F7 W- j- I0182 LX0.116Y23.999Z-2.
0183 LX-43.523Y23.999Z-2.
0184 LX-43.523Y-23.123Z-2.
( C$ {: g/ d( f! ^7 w& g  K' L( D0185 LX43.755Y-23.123Z-2.
2 `" n& [4 Q9 F' L, N3 R, b& }0186 LX43.755Y23.999Z-2.
" r+ ^% Z$ Y2 W7 j0187 LX0.116Y23.999Z-2.
# N& M. d) ]0 t2 g3 A5 m0188 LX0.116Y26.999Z-2.
0189 LX-46.523Y26.999Z-2.
0190 LX-46.523Y-26.123Z-2.
0191 LX46.755Y-26.123Z-2.
0192 LX46.755Y26.999Z-2.
0193 LX0.116Y26.999Z-2.
0194 LX0.116Y29.999Z-2.
0195 LX-49.523Y29.999Z-2.
0196 LX-49.523Y-29.123Z-2.
, O( Q& ]+ {( P4 \) n0197 LX49.755Y-29.123Z-2.
' w. P, w; o  S! B0198 LX49.755Y29.999Z-2.
! H2 ]% w6 D3 N6 D. N: |4 p3 N$ |! s0199 LX0.116Y29.999Z-2.
4 ?% Z  ?- z0 x5 G9 I0200 LX0.116Y32.999Z-2.
0201 LX-52.523Y32.999Z-2.
0202 LX-52.523Y-32.123Z-2.
" V" p/ P$ w+ N9 \7 p1 ?9 a* `0203 LX52.755Y-32.123Z-2.
* V3 ?- Z" m( H, w' a1 u- p' x0204 LX52.755Y32.999Z-2.
0205 LX0.116Y32.999Z-2.
5 R( A( I! B3 s. `0206 LX0.116Y35.999Z-2.
- G) q2 n" m' Y1 ]- d) Q+ O0207 LX-55.523Y35.999Z-2.
0208 LX-55.523Y-35.123Z-2.
0209 LX55.755Y-35.123Z-2.
/ A) b; h  X6 M( }9 O0210 LX55.755Y35.999Z-2.
0211 LX0.116Y35.999Z-2.
0212 LX0.116Y38.999Z-2.
$ B3 ^$ [0 ^; u& \: g" O' {0213 LX-58.523Y38.999Z-2.
; s# g* n) ?5 ~+ B8 f" W  K& L0214 LX-58.523Y-38.123Z-2.
( C( }" m( X3 e6 [) S0215 LX58.755Y-38.123Z-2.
0216 LX58.755Y38.999Z-2.
0217 LX0.116Y38.999Z-2.
4 d+ l0 I+ b7 l+ o; K( t; w# w0218 LX-2.884Y38.999Z-2.
0219 LX-2.884Y37.499Z-2.
! L8 \& }8 h. q0220 LX-2.884Y37.499Z10.FMAX
4 d* b9 t" U) U5 D' J- {) b0221 LX-2.884Y37.499Z100.FMAX
0222 LX0.Y0.Z100.FMAX
! S7 R. @+ n, c$ c" B" j1 m- Q4 M0223 CYCL DEF 32.0 TOLERANCE
# t; N, M" X% ^6 X4 _0224 CYCL DEF 32.1
0225 ;(F BLADE=2)
( \: T0 D4 X5 f0226 ;(F DIAM=8.0000,FLAT)
6 H$ g/ G7 k% f" b& Y8 P0227 TOOL CALL 09 Z S10000
+ l6 D( V+ e  V, {3 C: e1 B0228 M03
( m* t7 z+ [/ \: q6 i4 g1 n0 U& D6 S0087 CYCL DEF 9.0 DWELL TIME
# H8 }& J$ D7 B. @0087 CYCL DEF 9.1 DWELL 20 暂停20秒暖机
2 N  V) n! m! _9 C5 b0229 TCH PROBE 583 TOOL SETTING LEN ~
0230 Q350=+0  ;MEASURING TYPE ~
" h' r5 @. Z' k0231 Q361=+3  ;NUMBER OF MEASURINGS ~
8 {( @4 C5 E6 g2 d. |5 d) k0232 Q362=+0.01  ;DISPERSION TOLERANCE ~
1 T( S8 U0 H7 \6 F6 F0233 Q359=+0  ;ADD. LENGTH CORRECT.
0234 CYCL DEF 32.0 TOLERANCE
0235 CYCL DEF 32.1 T0.007
2 N( ]! d# ^4 I3 D( @  @, j0 O0236 M03
8 c: I% N& F) t' n1 j0237 LX0.Y0.FMAX
0238 LZ100.FMAX
2 d; }" \# H7 c- o) W0239 LX68.Y0.Z100.FMAX
0240 LX68.Y0.Z4.FMAX
4 S' {: [  i! f. t( e0241 M08
0242 LX68.Y0.Z-1.F1500
0243 LX68.Y5.Z-1.F1000
0244 CCX68.Y0.
0245 CX63.Y0.DR+
, O' |$ |' E" m4 M1 d5 G0246 LX63.Y-43.Z-1.
, {  g& [6 X, \$ L& h& C0247 LX-63.Y-43.Z-1.
# t4 T, G6 G: U% T. A9 L% I0248 LX-63.Y43.Z-1.
0249 LX63.Y43.Z-1.
1 z: x6 w, H" \* R0250 LX63.Y0.Z-1.
7 n6 p4 U/ r$ P% W. w0251 CCX68.Y0.
5 s7 I4 p0 j$ z$ g8 J# y0252 CX68.Y-5.DR+
4 I+ K# o. P( Z; l7 ]3 Z- t' @# Y0253 LX68.Y0.Z-1.
0254 LX68.Y0.Z-2.
: {( L+ x( `7 F- ?0 z1 k- b0255 LX68.Y5.Z-2.
0256 CCX68.Y0.
0257 CX63.Y0.DR+
0258 LX63.Y-43.Z-2.
0259 LX-63.Y-43.Z-2.
: q. S  `2 I+ Y7 ]! [% w* {0260 LX-63.Y43.Z-2.
0261 LX63.Y43.Z-2.
7 ^: S9 ~! Q+ P% L0262 LX63.Y0.Z-2.
0263 CCX68.Y0.
8 A, ?0 y6 t4 `2 [/ l; ~& w% ^7 k0264 CX68.Y-5.DR+
0265 LX68.Y0.Z-2.
0266 LX68.Y0.Z-3.
# O; v5 n& E) \$ F4 ?& G4 M0267 LX68.Y5.Z-3.
5 N* B! v2 K& m1 J0268 CCX68.Y0.
; ?( ]4 s  I" c' F/ s0269 CX63.Y0.DR+
+ P1 m8 z  Z8 k/ Y3 T7 C  T0270 LX63.Y-43.Z-3.
0271 LX-63.Y-43.Z-3.
0272 LX-63.Y43.Z-3.
5 Z/ L4 `0 H/ B! F4 j0273 LX63.Y43.Z-3.
3 _5 T+ K/ f: s3 |2 O& ?0274 LX63.Y0.Z-3.
1 N* S* N. r3 _' f0275 CCX68.Y0.
0276 CX68.Y-5.DR+
0277 LX68.Y0.Z-3.
3 E3 r6 ~4 E( {1 S6 v4 }! ^0278 LX68.Y0.Z10.FMAX
0279 LX68.Y0.Z100.FMAX
0280 LX0.Y0.Z100.FMAX
0281 CYCL DEF 32.0 TOLERANCE
: s* J  |  X$ v' M# v0282 CYCL DEF 32.1
0283 ENDPGM3333MM

djaho

上两个月买了一床1.8M的蕾舒床垫,太失望了,做工差,只用了一个多用就开始变形了,里面的弹簧突出来了,这是床垫吗!?还有说好送到楼下,就送到物流点就不送过来了,说要我们自提,之后联系他们店长,说支付100元给我们,到最后还没有支付!跟他们纠结了半个月了还是这样子,算了,当给钱给他们的店长买药吃!服务差,态度差,还有质量差!

1900

uop800有后处理吗?!

zhilin.zhang

至于机床我不做表态我个人认为海德汉系统是相当不错的，大多用于高端机上。

374601

不错，继续五轴的后处理

过眼云烟

都是高手，小弟刚接触海德汉，还玩不转